Page Comparison

source /etc/platform/openrc

NODE=controller-0
OAM_IF=<OAM-PORT>

# if you use flat oam network
system host-if-modify ${NODE} $OAM_IF -c platform
system interface-network-assign ${NODE} $OAM_IF oam

# if you use vlan oam network
VLANID=<VLAN-ID>
system host-if-modify -n pltif -c platform $NODE $OAM_IF
system host-if-add ${NODE} -V $VLANID -c platform oam0 vlan pltif
system interface-network-assign ${NODE} oam0 oam

system host-label-assign $NODE sriovdp=enabled
system host-label-assign $NODE kube-topology-mgr-policy=restricted

# Ceph backend for k8s pvc
system storage-backend-add ceph --confirmed
system host-disk-list ${NODE} | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add ${NODE} {}

# isolate cpus depends on number of the physical core
system host-cpu-modify -f application-isolated -p0 28 $NODE

# allocate/enable hugepages for DPDK usage
system host-memory-modify $NODE -1G 10 0

system host-unlock $NODE

source /etc/platform/openrc

NODE=controller-0
system host-lock $NODE

# get the device name of the Mount Bryce, we assume it is
# pci_0000_8a_00_0 here.
system host-device-list $NODE

# Modify the Mount Bryce device to enable it, specify the base driver
# and vf driver, and configure it for 1 VFs

# NOTE: If this is the initial install and have not unlocked, you will
# get following error message.
# Cannot configure device 73b13ddf-99be-44c8-8fbe-db85eb8d99ba until host
# controller-0 is unlocked for the first time.
system host-device-modify $NODE pci_0000_8a_00_0 -e true --driver igb_uio --vf-driver vfio -N 1

system host-unlock $NODE

cat >  volume-ceph.yaml << 'EOF'
kind: PersistentVolumeClaim
apiVersion: v1
metadata:
  name: flexran-storage
spec:
  accessModes:
    - ReadWriteOnce
  resources:
    requests:
      storage: 80Gi
  storageClassName: general
EOF

controller-0:~$ kubectl create -f volume-ceph.yaml
persistentvolumeclaim/flexran-storage created
controller-0:~$ kubectl get pvc
NAME              STATUS   VOLUME                                     CAPACITY   ACCESS MODES   STORAGECLASS   AGE
flexran-storage   Bound    pvc-43e50806-785f-440b-8ed2-85bb3c9e8f79   80Gi       RWO            general        9s

mkdir dockerbuilder && cd dockerbuilder

# prepare the artifacts used for FlexRAN prebuilt binary Docker image
mkdir docker-image-building
cat >  docker-image-building/readme << 'EOF'
# Instructions of Docker image generation

# Following steps are supposed to be executed inside building Pod,
# after building FlexRAN from source code

flxr_install_dir=/opt/fb/flexran/

# populate flexran related env var
cd ${flxr_install_dir}
source set_env_var.sh -d

# prepare the FlexRAN binaries
./transport.sh

# build the Docker image
docker build -t flr-run -f Dockerfile .

# tag and push
orgname=somename
docker tag flr-run ${orgname}/flr-run

EOF

cat >  docker-image-building/transport.sh << 'EOF'
#!/bin/bash

# ICXPATH=/opt/fb/intel/oneapi/

echo "Make sure source setvars.sh first.(located in ICX oneapi installation directory)"
echo "Make sure source set_env_var.sh -d first.(located in FlexRAN installation directory)"

[[ -z "$MKLROOT" ]] && { echo "MKLROOT not set, exit..."; exit 1; }
[[ -z "$IPPROOT" ]] && { echo "MKLROOT not set, exit..."; exit 1; }
[[ -z "$CMPLR_ROOT" ]] && { echo "MKLROOT not set, exit..."; exit 1; }
[[ -z "$DIR_WIRELESS_SDK_ROOT" ]] && { echo "DIR_WIRELESS_SDK_ROOT not set, exit..."; exit 1; }

FLXPATH=`echo $DIR_WIRELESS_SDK_ROOT| awk -F '/sdk' '{print $1}'`

[[ -d stuff ]] && { echo "Directory stuff exists, move it to old."; mv -f stuff stuff.old; }

mkdir stuff; cd stuff

mkdir libs
cp -a $MKLROOT/lib/intel64/libmkl_intel_lp64.so* libs
cp -a $MKLROOT/lib/intel64/libmkl_core.so* libs
cp -a $MKLROOT/lib/intel64/libmkl_intel_thread.so* libs
cp -a $MKLROOT/lib/intel64/libmkl_avx512.so.* libs
cp -a $MKLROOT/lib/intel64/libmkl_avx2.so* libs
cp -a $MKLROOT/lib/intel64/libmkl_avx.so* libs

cp -a $IPPROOT/lib/intel64/libipps.so* libs
cp -a $IPPROOT/lib/intel64/libippe.so* libs
cp -a $IPPROOT/lib/intel64/libippcore.so* libs
cp -a $IPPROOT/lib/intel64/libippee9.so* libs
cp -a $IPPROOT/lib/intel64/libippse9.so* libs

cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libiomp5.so* libs
cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libirc.so* libs
cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libimf.so* libs
cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libsvml.so* libs
cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libintlc.so* libs
cp -a $CMPLR_ROOT/linux/compiler/lib/intel64_lin/libirng.so* libs

cp -a $FLXPATH/libs/cpa/bin/libmmwcpadrv.so* libs
cp -a $FLXPATH/wls_mod/libwls.so* libs

mkdir -p flexran/sdk/build-avx512-icx/
cp -rf $FLXPATH/sdk/build-avx512-icx/source flexran/sdk/build-avx512-icx/
cp -rf $FLXPATH/sdk/build-avx512-icx/install flexran/sdk/build-avx512-icx/
cp -rf $FLXPATH/bin flexran/
cp -rf $FLXPATH/set_env_var.sh flexran/

# testcase files
mkdir -p tests/nr5g/
cd tests/nr5g/
for cfg in $FLXPATH/bin/nr5g/gnb/testmac/icelake-sp/*.cfg
do
  cat $cfg | grep TEST_FD > /tmp/$$.testfile
  while IFS= read line
  do
    array=($(echo "$line" | sed 's/5GNR,/ /g'))
    for i in "${array[@]}"; do
      if [[ "$i" =~ \.cfg ]]; then
        casedir=`echo "$i"| cut -d / -f 1-3 | xargs`
        caseabsdir=$FLXPATH/tests/nr5g/$casedir
        [[ ! -d $casedir ]] && { mkdir -p $casedir; cp -rf $caseabsdir/* $casedir; }
      fi
    done
  done < /tmp/$$.testfile
done

echo "Transportation Completed."
EOF

chmod a+x docker-image-building/transport.sh

cat >  docker-image-building/set-l1-env.sh << 'EOF'
# source this script to l1 binary location

export WORKSPACE=/root/flexran
export isa=avx512

cd $WORKSPACE
source ./set_env_var.sh -i ${isa}

MODE=$1
[[ -z "$MODE" ]] && read -p "Enter the MODE(LTE or 5G): " MODE

if [ $MODE = LTE ]; then
  cd $WORKSPACE/bin/lte/l1/
fi
if [ $MODE = 5G ]; then
  cd $WORKSPACE/bin/nr5g/gnb/l1
fi
EOF

cat >  docker-image-building/set-l2-env.sh << 'EOF'
# source this script to l2 binary location

export WORKSPACE=/root/flexran
export isa=avx512

cd $WORKSPACE
source ./set_env_var.sh -i ${isa}

MODE=$1
[[ -z "$MODE" ]] && read -p "Enter the MODE(LTE or 5G): " MODE

if [ $MODE = LTE ]; then
  cd $WORKSPACE/bin/lte/testmac/
fi
if [ $MODE = 5G ]; then
  cd $WORKSPACE/bin/nr5g/gnb/testmac
fi
EOF

cat >  docker-image-building/res-setup.sh << 'EOF'
#!/bin/bash

[[ -z "$PCIDEVICE_INTEL_COM_INTEL_ACC100_FEC" ]] && { echo "ACC100 not used, sleep..."; sleep infinity; }

sed -i 's#.*dpdkBasebandFecMode.*#        <dpdkBasebandFecMode\>1</dpdkBasebandFecMode>#' /root/flexran/bin/nr5g/gnb/l1/phycfg_timer.xml
sed -i 's#.*dpdkBasebandDevice.*#        <dpdkBasebandDevice\>'"$PCIDEVICE_INTEL_COM_INTEL_ACC100_FEC"'</dpdkBasebandDevice>#' /root/flexran/bin/nr5g/gnb/l1/phycfg_timer.xml

echo "Resource setup Completed, sleep..."
sleep infinity
EOF

chmod a+x docker-image-building/res-setup.sh

mkdir docker-image-building/rootdir
mv docker-image-building/res-setup.sh docker-image-building/rootdir
mv docker-image-building/set-l1-env.sh docker-image-building/rootdir
mv docker-image-building/set-l2-env.sh docker-image-building/rootdir

cat >  docker-image-building/Dockerfile << 'EOF'
FROM centos:7.9.2009

RUN [ -e /etc/yum.conf ] && sed -i '/tsflags=nodocs/d' /etc/yum.conf || true

RUN yum install -y libhugetlbfs* libstdc++* numa* gcc g++ iproute \
           module-init-tools kmod pciutils python libaio libaio-devel \
           numactl-devel nettools ethtool
RUN yum clean all

COPY stuff/libs/* /usr/lib64/

WORKDIR /root/
COPY stuff/flexran ./flexran
COPY stuff/tests ./flexran/tests
COPY rootdir/* ./

CMD ["/root/res-setup.sh"]
EOF

cat >  Dockerfile << 'EOF'
FROM centos:7.9.2009

RUN [ -e /etc/yum.conf ] && sed -i '/tsflags=nodocs/d' /etc/yum.conf || true

RUN yum groupinstall -y 'Development Tools'

RUN yum install -y vim gcc-c++ libhugetlbfs* libstdc++* kernel-devel numa* gcc git mlocate \
           cmake wget ncurses-devel hmaccalc zlib-devel binutils-devel elfutils-libelf-devel \
           numactl-devel libhugetlbfs-devel bc patch git patch tar zip unzip python3 sudo docker

RUN yum install -y gtk3 mesa-libgbm at-spi2-core libdrm xdg-utils libxcb libnotify

RUN yum install -y centos-release-scl
RUN yum install -y devtoolset-8

RUN yum clean all

RUN pip3 install meson && \
    pip3 install ninja pyelftools

# ENV HTTP_PROXY=""
# ENV HTTPS_PROXY=""

WORKDIR /usr/src/
RUN git clone https://github.com/pkgconf/pkgconf.git
WORKDIR /usr/src/pkgconf
RUN ./autogen.sh && ./configure && make && make install

WORKDIR /usr/src/
RUN git clone git://git.kernel.org/pub/scm/utils/rt-tests/rt-tests.git
WORKDIR /usr/src/rt-tests
RUN git checkout stable/v1.0
RUN make all && make install

COPY docker-image-building /root/docker-image-building

WORKDIR /opt

# Set default command
CMD ["/usr/bin/bash"]
EOF

# build the Docker image for FlexRAN building environment
sudo docker build -t flexran-builder .
sudo docker tag flexran-builder registry.local:9001/flexran-builder:22.03

# push to registry.local:9001
sudo docker login registry.local:9001 -u admin -p <your_sysadmin_passwd>
sudo docker push registry.local:9001/flexran-builder:22.03

cat >  flexran-buildpod.yml << 'EOF'
apiVersion: v1
kind: Pod
metadata:
  name: buildpod
  annotations:
spec:
  restartPolicy: Never
  containers:
  - name: buildpod
    image: registry.local:9001/flexran-builder:22.03
    imagePullPolicy: IfNotPresent
    volumeMounts:
    - name: usrsrc
      mountPath: /usr/src
    - mountPath: /hugepages
      name: hugepage
    - name: lib-modules
      mountPath: /lib/modules
    - name: pvc1
      mountPath: /opt/fb
    - name: docker-sock-volume
      mountPath: /var/run/docker.sock
    command: ["/bin/bash", "-ec", "sleep infinity"]
    securityContext:
      privileged: true
      capabilities:
        add:
          ["IPC_LOCK", "SYS_ADMIN"]
    resources:
      requests:
        memory: 32Gi
        hugepages-1Gi: 10Gi
        intel.com/intel_acc100_fec: '1'
      limits:
        memory: 32Gi
        intel.com/intel_acc100_fec: '1'
        hugepages-1Gi: 10Gi
  volumes:
  - name: usrsrc
    hostPath:
      path: /usr/src
  - name: lib-modules
    hostPath:
      path: /lib/modules
  - name: hugepage
    emptyDir:
        medium: HugePages
  - name: docker-sock-volume
    hostPath:
      path: /var/run/docker.sock
      type: Socket
  - name: pvc1
    persistentVolumeClaim:
      claimName: flexran-storage
EOF

kubectl create -f flexran-buildpod.yml

kubectl exec -it buildpod -- bash

mkdir -p /opt/fb/scratch && cd /opt/fb/scratch
scp <options> FlexRAN-22.03-L1.tar.gz_part00 .
scp <options> FlexRAN-22.03-L1.tar.gz_part01 .
scp <options> dpdk_patch-22.03.patch .

cat FlexRAN-22.03-L1.tar.gz_part00 FlexRAN-22.03-L1.tar.gz_part01 > FlexRAN-22.03-L1.tar.gz
rm FlexRAN-22.03-L1.tar.gz_part00
rm FlexRAN-22.03-L1.tar.gz_part01

source /opt/fb/intel/oneapi/setvars.sh
cd /opt/fb/flexran && source ./set_env_var.sh -d

cd /root/docker-image-building
./transport.sh

docker build -t flr-run -f Dockerfile .

# change to host side, in this case, it should be controller-0 host
sudo docker login registry.local:9001 -u admin -p <your_sysadmin_passwd>
sudo docker tag flr-run registry.local:9001/flxrun:22.03
sudo docker push registry.local:9001/flxrun:22.03

cat > runpod-flxr.yml << 'EOF'
apiVersion: v1
kind: Pod
metadata:
  name: runpod
  annotations:
spec:
  restartPolicy: Never
  containers:
  - name: runpod
    image: registry.local:9001/flxrun:22.03
    imagePullPolicy: IfNotPresent
    volumeMounts:
    - mountPath: /hugepages
      name: hugepage
    securityContext:
      privileged: false
      capabilities:
        add:
          ["IPC_LOCK", "SYS_ADMIN", "SYS_NICE"]
    resources:
      requests:
        memory: 32Gi
        hugepages-1Gi: 6Gi
        intel.com/intel_acc100_fec: '1'
      limits:
        memory: 32Gi
        hugepages-1Gi: 6Gi
        intel.com/intel_acc100_fec: '1'
  volumes:
  - name: hugepage
    emptyDir:
        medium: HugePages
EOF

kubectl create -f runpod-flxr.yml

kubectl exec -it runpod -- bash
s
5G

phycfg_timer.xml has been modified by entry script to use the FEC accelerator: <dpdkBasebandFecMode>1</dpdkBasebandFecMode> <dpdkBasebandDevice>0000:8b:00.0</dpdkBasebandDevice>

This configuration is scripted and runs automatically, no manual configuration is needed. You can use printenv PCIDEVICE_INTEL_COM_INTEL_ACC100_FEC to check dpdkBasebandDevice.

# change default CPU binding in section of <Threads> in phycfg_timer.xml
# use the first 3 assigned CPUs for the Applications threads

<!-- CPU Binding to Application Threads -->
    <Threads>
        <!-- System Threads (Single core id value): Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <systemThread>2, 0, 0</systemThread>

        <!-- Timer Thread (Single core id value): Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <timerThread>3, 96, 0</timerThread>

        <!-- FPGA for LDPC Thread (Single core id value): Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <FpgaDriverCpuInfo>4, 96, 0</FpgaDriverCpuInfo>

        <!-- FPGA for Front Haul (FFT / IFFT) Thread (Single core id value): Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <!-- This thread should be created for timer mode and hence can be same core as LDPC polling core -->
        <FrontHaulCpuInfo>4, 96, 0</FrontHaulCpuInfo>

        <!-- DPDK Radio Master Thread (Single core id value): Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <radioDpdkMaster>2, 99, 0</radioDpdkMaster>
    </Threads>

# launch L1app
./l1.sh -e

kubectl exec -it runpod -- bash
source set-l2-env.sh 5G

# Modify default CPU binding in section of <Threads> in testmac_cfg.xml
# Make sure to use the CPU from the CPU whose ID is bigger than 13,
# this way, the Application Threads will not overlap with the BBUPool CPUs.
<!-- CPU Binding to Application Threads -->
    <Threads>
        <!-- Wireless Subsystem Thread: Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <wlsRxThread>16, 90, 0</wlsRxThread>

        <!-- System Threads: Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <systemThread>14, 0, 0</systemThread>

        <!-- TestMac Run Thread: Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <runThread>14, 89, 0</runThread>

        <!-- Thread to send / receive URLLC APIS to / from testmac to Phy. It will be created only when the phy_config has URLLC Support added to it: Core, priority, Policy [0: SCHED_FIFO 1: SCHED_RR] -->
        <urllcThread>15, 90, 0</urllcThread>
    </Threads>

# workaround the known issue of parsing zero value in the config file
sed -i '/>0</d' testmac_cfg.xml

# launch testmac
./l2.sh --testfile=icelake-sp/icxsp_mu1_100mhz_mmimo_64x64_16stream_hton.cfg

# Note, case of 3389 is the most stringent case, we can comment out
# other cases in the file and run this case directly:
# TEST_FD, 3389, 3, 5GNR, fd/mu1_100mhz/383/fd_testconfig_tst383.cfg,
# 5GNR, fd/mu1_100mhz/386/fd_testconfig_tst386.cfg,
# 5GNR, fd/mu1_100mhz/386/fd_testconfig_tst386.cfg